install.sh aktualisiert

Config.txt hinzugefügt

README.md

@@ -1,7 +1,7 @@
 # RPS-Client
 
 ```bash
-wget -qO- --header 'Authorization:token 9031f8d227dd83ba601680bf3a9f6c2d26c1a970' https://gitea.int.eertmoed.net/WiS/RPS-Client/archive/latest.tar.gz | tar xvz ; bash ./rps-client/install.sh ;
+wget -qO- --header 'Authorization:token 9031f8d227dd83ba601680bf3a9f6c2d26c1a970' https://gitea.int.eertmoed.net/WiS/RPS-Client/archive/latest.tar.gz | tar xvz ; bash /root/rps-client/install.sh ;
 ```
 
 ```ruby

boot/firmware/ro-root.sh

@@ -1,120 +0,0 @@
-#!/bin/sh
-
-#  Read-only Root-FS for Raspian using overlayfs
-#  Version 1.1:
-#  Changed to use /proc/mounts rathern than /etc/fstab for deriving the root filesystem.
-#
-#  Version 1:
-#  Created 2017 by Pascal Suter @ DALCO AG, Switzerland to work on Raspian as custom init script
-#  (raspbian does not use an initramfs on boot)
-#
-#  This program is free software: you can redistribute it and/or modify
-#  it under the terms of the GNU General Public License as published by
-#  the Free Software Foundation, either version 3 of the License, or
-#  (at your option) any later version.
-#
-#  This program is distributed in the hope that it will be useful,
-#  but WITHOUT ANY WARRANTY; without even the implied warranty of
-#  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-#  GNU General Public License for more details.
-#
-#    You should have received a copy of the GNU General Public License
-#    along with this program.  If not, see
-#    <http://www.gnu.org/licenses/>.
-#
-#
-#  Tested with Raspbian mini, 2017-01-11
-#
-#  This script will mount the root filesystem read-only and overlay it with a temporary tempfs
-#  which is read-write mounted. This is done using the overlayFS which is part of the linux kernel
-#  since version 3.18.
-#  when this script is in use, all changes made to anywhere in the root filesystem mount will be lost
-#  upon reboot of the system. The SD card will only be accessed as read-only drive, which significantly
-#  helps to prolong its life and prevent filesystem coruption in environments where the system is usually
-#  not shut down properly
-#
-#  Install:
-#  copy this script to /sbin/overlayRoot.sh and add "init=/sbin/overlayRoot.sh" to the cmdline.txt
-#  file in the raspbian image's boot partition.
-#  I strongly recommend to disable swapping before using this. it will work with swap but that just does
-#  not make sens as the swap file will be stored in the tempfs which again resides in the ram.
-#  run these commands on the booted raspberry pi BEFORE you set the init=/sbin/overlayRoot.sh boot option:
-#  sudo dphys-swapfile swapoff
-#  sudo dphys-swapfile uninstall
-#  sudo update-rc.d dphys-swapfile remove
-#
-#  To install software, run upgrades and do other changes to the raspberry setup, simply remove the init=
-#  entry from the cmdline.txt file and reboot, make the changes, add the init= entry and reboot once more.
-
-fail(){
-        echo -e "$1"
-        /bin/bash
-}
-
-# load module
-modprobe overlay
-if [ $? -ne 0 ]; then
-    fail "ERROR: missing overlay kernel module"
-fi
-# mount /proc
-mount -t proc proc /proc
-
-# create a writable fs to then create our mountpoints
-mount -t tmpfs inittemp /mnt
-if [ $? -ne 0 ]; then
-    fail "ERROR: could not create a temporary filesystem to mount the base filesystems for overlayfs"
-fi
-mkdir /mnt/lower
-mkdir /mnt/rw
-mount -t tmpfs root-rw /mnt/rw
-if [ $? -ne 0 ]; then
-    fail "ERROR: could not create tempfs for upper filesystem"
-fi
-mkdir /mnt/rw/upper
-mkdir /mnt/rw/work
-mkdir /mnt/newroot
-
-# mount root filesystem readonly
-rootDev=`awk '$2 == "/" {print $1}' /proc/mounts`
-rootMountOpt=`awk '$2 == "/" {print $4}' /proc/mounts`
-rootFsType=`awk '$2 == "/" {print $3}' /proc/mounts`
-mount -t ${rootFsType} -o ${rootMountOpt},ro ${rootDev} /mnt/lower
-if [ $? -ne 0 ]; then
-    fail "ERROR: could not ro-mount original root partition"
-fi
-mount -t overlay -o lowerdir=/mnt/lower,upperdir=/mnt/rw/upper,workdir=/mnt/rw/work overlayfs-root /mnt/newroot
-if [ $? -ne 0 ]; then
-    fail "ERROR: could not mount overlayFS"
-fi
-# create mountpoints inside the new root filesystem-overlay
-mkdir /mnt/newroot/ro
-mkdir /mnt/newroot/rw
-# remove root mount from fstab (this is already a non-permanent modification)
-grep -v "$rootDev" /mnt/lower/etc/fstab > /mnt/newroot/etc/fstab
-echo "#the original root mount has been removed by overlayRoot.sh" >> /mnt/newroot/etc/fstab
-echo "#this is only a temporary modification, the original fstab" >> /mnt/newroot/etc/fstab
-echo "#stored on the disk can be found in /ro/etc/fstab" >> /mnt/newroot/etc/fstab
-# change to the new overlay root
-cd /mnt/newroot
-pivot_root . mnt
-exec chroot . sh -c "$(cat <<END
-# move ro and rw mounts to the new root
-mount --move /mnt/mnt/lower/ /ro
-if [ $? -ne 0 ]; then
-    echo "ERROR: could not move ro-root into newroot"
-    /bin/bash
-fi
-mount --move /mnt/mnt/rw /rw
-if [ $? -ne 0 ]; then
-    echo "ERROR: could not move tempfs rw mount into newroot"
-    /bin/bash
-fi
-# unmount unneeded mounts so we can unmout the old readonly root
-umount /mnt/mnt
-umount /mnt/proc
-umount -l -f /mnt/dev
-umount -l -f /mnt
-# continue with regular init
-exec /sbin/init
-END
-)"

boot/ro-root.sh

@@ -1,120 +0,0 @@
-#!/bin/sh
-
-#  Read-only Root-FS for Raspian using overlayfs
-#  Version 1.1:
-#  Changed to use /proc/mounts rathern than /etc/fstab for deriving the root filesystem.
-#
-#  Version 1:
-#  Created 2017 by Pascal Suter @ DALCO AG, Switzerland to work on Raspian as custom init script
-#  (raspbian does not use an initramfs on boot)
-#
-#  This program is free software: you can redistribute it and/or modify
-#  it under the terms of the GNU General Public License as published by
-#  the Free Software Foundation, either version 3 of the License, or
-#  (at your option) any later version.
-#
-#  This program is distributed in the hope that it will be useful,
-#  but WITHOUT ANY WARRANTY; without even the implied warranty of
-#  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-#  GNU General Public License for more details.
-#
-#    You should have received a copy of the GNU General Public License
-#    along with this program.  If not, see
-#    <http://www.gnu.org/licenses/>.
-#
-#
-#  Tested with Raspbian mini, 2017-01-11
-#
-#  This script will mount the root filesystem read-only and overlay it with a temporary tempfs
-#  which is read-write mounted. This is done using the overlayFS which is part of the linux kernel
-#  since version 3.18.
-#  when this script is in use, all changes made to anywhere in the root filesystem mount will be lost
-#  upon reboot of the system. The SD card will only be accessed as read-only drive, which significantly
-#  helps to prolong its life and prevent filesystem coruption in environments where the system is usually
-#  not shut down properly
-#
-#  Install:
-#  copy this script to /sbin/overlayRoot.sh and add "init=/sbin/overlayRoot.sh" to the cmdline.txt
-#  file in the raspbian image's boot partition.
-#  I strongly recommend to disable swapping before using this. it will work with swap but that just does
-#  not make sens as the swap file will be stored in the tempfs which again resides in the ram.
-#  run these commands on the booted raspberry pi BEFORE you set the init=/sbin/overlayRoot.sh boot option:
-#  sudo dphys-swapfile swapoff
-#  sudo dphys-swapfile uninstall
-#  sudo update-rc.d dphys-swapfile remove
-#
-#  To install software, run upgrades and do other changes to the raspberry setup, simply remove the init=
-#  entry from the cmdline.txt file and reboot, make the changes, add the init= entry and reboot once more.
-
-fail(){
-        echo -e "$1"
-        /bin/bash
-}
-
-# load module
-modprobe overlay
-if [ $? -ne 0 ]; then
-    fail "ERROR: missing overlay kernel module"
-fi
-# mount /proc
-mount -t proc proc /proc
-
-# create a writable fs to then create our mountpoints
-mount -t tmpfs inittemp /mnt
-if [ $? -ne 0 ]; then
-    fail "ERROR: could not create a temporary filesystem to mount the base filesystems for overlayfs"
-fi
-mkdir /mnt/lower
-mkdir /mnt/rw
-mount -t tmpfs root-rw /mnt/rw
-if [ $? -ne 0 ]; then
-    fail "ERROR: could not create tempfs for upper filesystem"
-fi
-mkdir /mnt/rw/upper
-mkdir /mnt/rw/work
-mkdir /mnt/newroot
-
-# mount root filesystem readonly
-rootDev=`awk '$2 == "/" {print $1}' /proc/mounts`
-rootMountOpt=`awk '$2 == "/" {print $4}' /proc/mounts`
-rootFsType=`awk '$2 == "/" {print $3}' /proc/mounts`
-mount -t ${rootFsType} -o ${rootMountOpt},ro ${rootDev} /mnt/lower
-if [ $? -ne 0 ]; then
-    fail "ERROR: could not ro-mount original root partition"
-fi
-mount -t overlay -o lowerdir=/mnt/lower,upperdir=/mnt/rw/upper,workdir=/mnt/rw/work overlayfs-root /mnt/newroot
-if [ $? -ne 0 ]; then
-    fail "ERROR: could not mount overlayFS"
-fi
-# create mountpoints inside the new root filesystem-overlay
-mkdir /mnt/newroot/ro
-mkdir /mnt/newroot/rw
-# remove root mount from fstab (this is already a non-permanent modification)
-grep -v "$rootDev" /mnt/lower/etc/fstab > /mnt/newroot/etc/fstab
-echo "#the original root mount has been removed by overlayRoot.sh" >> /mnt/newroot/etc/fstab
-echo "#this is only a temporary modification, the original fstab" >> /mnt/newroot/etc/fstab
-echo "#stored on the disk can be found in /ro/etc/fstab" >> /mnt/newroot/etc/fstab
-# change to the new overlay root
-cd /mnt/newroot
-pivot_root . mnt
-exec chroot . sh -c "$(cat <<END
-# move ro and rw mounts to the new root
-mount --move /mnt/mnt/lower/ /ro
-if [ $? -ne 0 ]; then
-    echo "ERROR: could not move ro-root into newroot"
-    /bin/bash
-fi
-mount --move /mnt/mnt/rw /rw
-if [ $? -ne 0 ]; then
-    echo "ERROR: could not move tempfs rw mount into newroot"
-    /bin/bash
-fi
-# unmount unneeded mounts so we can unmout the old readonly root
-umount /mnt/mnt
-umount /mnt/proc
-umount -l -f /mnt/dev
-umount -l -f /mnt
-# continue with regular init
-exec /sbin/init
-END
-)"

data/config/.xinitrc

@@ -14,7 +14,8 @@ then
     xset s noblank
     xset s off
 else
-    xset s $SCREEN
+    xset +dpms
+    xset dmps 0 0 $SCREEN
 fi
 
 #NO-Var fallback site
@@ -23,7 +24,8 @@ then
 	WBS=https://www.wis.gmbh/
 fi
 
-#Start Chromium
+sudo systemctl start chromium-monitor
+
 chromium-browser $WBS \
   --window-size=$RES \
   --window-position=0,0 \

data/config/config.txt

@@ -0,0 +1,38 @@
+# --- Basis Boot Einstellungen ---
+disable_splash=1          # Kein Raspberry-Pi-Bootlogo
+boot_delay=0              # Kein Boot-Delay (schnellerer Start)
+initial_turbo=30          # CPU für 30 Sek. auf maximale Leistung setzen (schnelleres PXE-Boot)
+
+# --- Netzwerk PXE Boot ---
+program_usb_boot_mode=1   # Aktiviert USB/Netzwerk-Boot (nur einmalig nötig)
+bootcode_delay=1          # Reduziert Wartezeit beim Netzwerkboot
+
+# --- GPU & Video Settings (für 2 Monitore) ---
+gpu_mem=192               # 192 MB Grafikspeicher für stabilen Dual-Monitor-Betrieb
+max_framebuffers=2        # Unterstützt 2 Bildschirme
+hdmi_force_hotplug=1      # Erzwungene HDMI-Erkennung (wichtig bei Boot ohne angeschlossenen Monitor)
+hdmi_drive=1              # DVI-Modus (kein Audio über HDMI)
+hdmi_ignore_edid_audio=1  # HDMI-Audio komplett deaktivieren
+dtoverlay=vc4-kms-v3d     # KMS-Grafiktreiber für beste Kompatibilität
+
+# --- Display Konfiguration ---
+disable_overscan=1        # Deaktiviert Overscan für eine saubere Anzeige
+hdmi_group=2              # Modus für explizite Auflösungswahl
+hdmi_mode=82              # 1080p @ 60 Hz
+hdmi_blanking=1           # Reduziert Stromverbrauch bei ausgeschaltetem Bildschirm
+
+# --- Touchscreen Einstellungen (falls benötigt) ---
+dtoverlay=usbtouchscreen  # Aktiviert Unterstützung für HID-kompatible USB-Touchscreens
+dtoverlay=goodix          # Aktiviert Unterstützung für I2C-basierte Goodix-Touchscreens
+dtparam=i2c_arm=on        # Falls Touchscreen über I2C läuft
+
+# --- Deaktivierung von nicht benötigten Funktionen ---
+dtoverlay=disable-wifi    # WLAN abschalten
+dtoverlay=disable-bt      # Bluetooth abschalten
+dtparam=audio=off         # Onboard-Sound deaktivieren (spart Ressourcen)
+
+# --- Optimierung für Embedded-Betrieb (stabiler und stromsparender) ---
+force_turbo=0             # Kein permanentes Overclocking (längere Lebensdauer)
+arm_boost=1               # Automatische Taktoptimierung (nur auf RPi 4/400)
+temp_limit=75             # Max. Temperaturbegrenzung (75°C)
+over_voltage=0            # Keine Spannungsanpassung (stabil)

data/scripts/chromium-monitor

@@ -0,0 +1,51 @@
+#!/bin/bash 
+
+LOGFILE="/var/log/chromium-monitor.log"
+
+# Function to log messages with timestamps
+log() {
+    echo "$(date '+%Y-%m-%d %H:%M:%S') - $1" >> "$LOGFILE"
+}
+
+# Function to get the monitor value from DHCP
+get_monitor() {
+    sudo cat /var/lib/dhcp/* | grep -a "option monitor" | tail -1 | \
+    awk '{ s = ""; for (i = 3; i <= NF; i++) s = s $i " "; print s}' | \
+    awk -F '"' '{print $2}'
+}
+
+# Function to get the current window name
+get_current_window() {
+    DISPLAY=:0 xdotool getwindowfocus getwindowname
+}
+
+# Initialize monitor variable
+monitor=""
+while [ -z "$monitor" ]; do
+    monitor=$(get_monitor)
+    if [ -n "$monitor" ]; then
+        log "Initial monitor detected: $monitor"  # Log initial monitor
+    fi
+    sleep 5
+done
+
+# Main loop to continuously check the current window
+while true; do
+    current_window=$(get_current_window)  # Get the current window name
+
+    if [ -n "$current_window" ]; then
+        # Check for mismatch using case-insensitive comparison
+        if ! echo "$current_window" | grep -iq "$monitor"; then
+            log "Mismatch detected! Monitor: $monitor, Current: $current_window"
+            log "Rebooting now."
+            sudo reboot
+            exit 1
+        fi
+    fi
+
+    # Sleep for a short duration before the next check
+    sleep 5
+done
+
+# Version 1.0:
+# Created 2024 by Tim Eertmoed, Christian Hampp @ WiS IT-Solutions GmbH, Germany to work on Raspbian as custom PXE init script.

data/scripts/hostname

@@ -2,6 +2,11 @@
 
 LOGFILE="/var/log/hostname.log"
 
+# Function to log messages with timestamps
+log() {
+    echo "$(date '+%Y-%m-%d %H:%M:%S') - $1" >> "$LOGFILE"
+}
+
 # Function to read the hostname from the DHCP lease file
 get_hostname() {
     sudo cat /var/lib/dhcp/* | grep -a "option host-name" | tail -1 | \
@@ -13,7 +18,7 @@ update_hosts() {
     local hostname="$1"
     # Replace the second line with the new hostname
     sudo sed -i "2s/.*/127.0.1.1   ${hostname}/" /etc/hosts
-    echo "Updated /etc/hosts with hostname: $hostname" >> $LOGFILE
+    log "Updated /etc/hosts with hostname: $hostname"
 }
 
 # Read the hostname from DHCP
@@ -22,14 +27,14 @@ hostname=$(get_hostname)
 if [ -n "$hostname" ]; then
     # Set the hostname using hostnamectl
     sudo hostnamectl set-hostname "$hostname"
-    echo "Set hostname to: $hostname" >> $LOGFILE
+    log "Set hostname to: $hostname"
     update_hosts "$hostname"
 else
-    echo "No hostname found." >> $LOGFILE
+    log "No hostname found."
 fi
 
 # Log completion
-echo "Hostname update script completed." >> $LOGFILE
+log "Hostname update script completed."
 
-#  Version 1.0:
+# Version 1.0:
-#  Created 2024 by Tim Eertmoed, Christian Hampp @ WiS IT-Solutions GmbH, Germany to work on Raspian as custom pxe init script.
+# Created 2024 by Tim Eertmoed, Christian Hampp @ WiS IT-Solutions GmbH, Germany to work on Raspbian as custom PXE init script.

data/scripts/overlayRoot.sh

@@ -0,0 +1,70 @@
+#!/bin/bash
+
+# Dieses Skript wird das Root-Dateisystem schreibgeschützt einbinden und es mit einem temporären tmpfs-Overlay versehen.
+#
+# Installation:
+# Kopiere dieses Skript nach /sbin/overlayRoot.sh und füge "init=/sbin/overlayRoot.sh" zur cmdline.txt-Datei
+# in der Boot-Partition des Raspbian-Images hinzu.
+#
+# Führe die folgenden Befehle als root aus:
+# sudo dphys-swapfile swapoff
+# sudo dphys-swapfile uninstall
+# sudo update-rc.d dphys-swapfile remove
+#
+# Um Software zu installieren, Upgrades durchzuführen und andere Änderungen an der Raspberry-Konfiguration vorzunehmen,
+# entferne einfach den Eintrag "init=/sbin/overlayRoot.sh" aus der cmdline.txt-Datei und starte das System neu.
+# Nimm die gewünschten Änderungen vor, füge den init= Eintrag wieder hinzu und starte erneut neu.
+
+set -e
+fail() {
+    echo -e "$1" >&2
+    exit 1
+}
+
+# Prüfen und Modul laden
+modprobe overlay || fail "ERROR: OverlayFS-Modul nicht geladen."
+
+# /proc einbinden
+mountpoint -q /proc || mount -t proc proc /proc
+
+# Temporäres Dateisystem für Overlay erstellen
+mount -t tmpfs tmpfs /overlay || fail "ERROR: tmpfs konnte nicht gemountet werden."
+mkdir -p /overlay/lower /overlay/rw/upper /overlay/rw/work /overlay/newroot
+
+# Root-Dateisystem schreibgeschützt einbinden
+rootDev=$(awk '$2 == "/" {print $1}' /proc/mounts)
+rootMountOpt=$(awk '$2 == "/" {print $4}' /proc/mounts)
+rootFsType=$(awk '$2 == "/" {print $3}' /proc/mounts)
+
+mount -t "${rootFsType}" -o "${rootMountOpt},ro" "${rootDev}" /overlay/lower || \
+    fail "ERROR: Ursprüngliches Root-Dateisystem konnte nicht schreibgeschützt eingebunden werden."
+
+# OverlayFS einbinden
+mount -t overlay \
+    -o lowerdir=/overlay/lower,upperdir=/overlay/rw/upper,workdir=/overlay/rw/work \
+    overlay /overlay/newroot || fail "ERROR: OverlayFS konnte nicht gemountet werden."
+
+# Neue Root-Overlay-Verzeichnisse erstellen
+mkdir -p /overlay/newroot/overlay/ro /overlay/newroot/overlay/rw
+
+# Originale fstab modifizieren
+grep -v "$rootDev" /overlay/lower/etc/fstab > /overlay/newroot/etc/fstab
+cat <<EOF >> /overlay/newroot/etc/fstab
+# Das originale Root-Dateisystem wurde durch overlayRoot.sh entfernt.
+# Diese änderung ist temporär. Die originale fstab ist in /overlay/ro/etc/fstab verfügbar.
+EOF
+
+# Root wechseln und alte Root aufräumen
+cd /overlay/newroot
+pivot_root . overlay || fail "ERROR: pivot_root fehlgeschlagen."
+
+exec chroot . /bin/bash -c "
+    mount --move /overlay/overlay/lower /overlay/ro || fail 'ERROR: /ro konnte nicht verschoben werden.'
+    mount --move /overlay/overlay/rw /overlay/rw || fail 'ERROR: /rw konnte nicht verschoben werden.'
+    umount /overlay/overlay || true
+    umount /overlay/proc || true
+    umount -l -f /overlay/dev || true
+    umount -l -f /overlay || true
+
+    exec /sbin/init
+"

data/scripts/ramfsRoot.sh

@@ -0,0 +1,44 @@
+#!/bin/bash
+set -e
+
+fail() {
+    echo -e "$1" >&2
+    exit 1
+}
+
+# Prüfen, ob genügend RAM frei ist (in KB)
+RAM_FREE=$(grep MemAvailable /proc/meminfo | awk '{print $2}')
+if [ "$RAM_FREE" -lt 3000000 ]; then  # 3GB als Mindestgrenze
+    fail "Nicht genügend freier RAM!"
+fi
+
+# RAMFS als neues Root mounten
+echo "Erstelle RAM-basiertes Root-Dateisystem..."
+mount -t ramfs -o mode=0755 ramfs /mnt || fail "Fehler beim Mounten von ramfs"
+
+# Sicherstellen, dass notwendige Verzeichnisse existieren
+mkdir -p /mnt/{proc,sys,dev,run,tmp}
+
+# Komplettes Root-Dateisystem nach RAMFS kopieren
+echo "Kopiere System nach RAM..."
+cp -ax / /mnt || fail "Fehler beim Kopieren nach RAMFS"
+
+# Mountpunkte ins neue Root verschieben
+mount --move /proc /mnt/proc
+mount --move /sys /mnt/sys
+mount --move /dev /mnt/dev
+mount --move /run /mnt/run
+
+# Wechsle zum neuen Root-FS
+cd /mnt
+pivot_root . oldroot || fail "pivot_root fehlgeschlagen"
+
+# Altes Root unmounten
+umount -l /oldroot/proc || true
+umount -l /oldroot/sys || true
+umount -l /oldroot/dev || true
+umount -l /oldroot/run || true
+umount -l /oldroot || true
+
+# Startet das System normal weiter
+exec /sbin/init

data/scripts/squashfsRoot.sh

@@ -0,0 +1,50 @@
+#!/bin/bash
+set -e
+
+fail() {
+    echo -e "$1" >&2
+    exit 1
+}
+
+echo "Lade SquashFS-Root in den RAM..."
+
+# Prüfen, ob genügend RAM verfügbar ist
+RAM_FREE=$(grep MemAvailable /proc/meminfo | awk '{print $2}')
+if [ "$RAM_FREE" -lt 1000000 ]; then  # Mindestens 1GB RAM nötig
+    fail "Nicht genügend freier RAM!"
+fi
+
+# RAMFS für SquashFS-Image erstellen
+mount -t ramfs -o mode=0755 ramfs /mnt || fail "Fehler beim Mounten von ramfs"
+
+# SquashFS-Image nach RAM laden (600-900 MB)
+cp /root.sqsh /mnt/root.sqsh || fail "Fehler beim Kopieren von SquashFS-Image"
+
+# SquashFS-Image mounten (Read-Only)
+mkdir -p /mnt/squashfs
+mount -t squashfs /mnt/root.sqsh /mnt/squashfs -o loop || fail "Fehler beim Mounten von SquashFS"
+
+# OverlayFS für Schreibzugriff einrichten
+mkdir -p /mnt/overlay/{upper,work,newroot}
+mount -t overlay overlay -o lowerdir=/mnt/squashfs,upperdir=/mnt/overlay/upper,workdir=/mnt/overlay/work /mnt/overlay/newroot || fail "Fehler beim Mounten von OverlayFS"
+
+# Mountpunkte ins neue Root verschieben
+mkdir -p /mnt/overlay/newroot/{proc,sys,dev,run,tmp}
+mount --move /proc /mnt/overlay/newroot/proc
+mount --move /sys /mnt/overlay/newroot/sys
+mount --move /dev /mnt/overlay/newroot/dev
+mount --move /run /mnt/overlay/newroot/run
+
+# Root wechseln
+cd /mnt/overlay/newroot
+pivot_root . oldroot || fail "pivot_root fehlgeschlagen"
+
+# Altes Root unmounten
+umount -l /oldroot/proc || true
+umount -l /oldroot/sys || true
+umount -l /oldroot/dev || true
+umount -l /oldroot/run || true
+umount -l /oldroot || true
+
+echo "SquashFS Root erfolgreich geladen. Starte init..."
+exec /sbin/init

data/scripts/watchdog-monitor

@@ -0,0 +1,99 @@
+#!/bin/bash
+
+# Log file
+log_file="/var/log/watchdog.log"
+
+# Configuration file
+config_file="/etc/watchdog.conf"
+
+# Function to log messages with timestamp
+log() {
+    echo "$(date '+%Y-%m-%d %H:%M:%S') - $1" >> "$log_file"
+}
+
+# Function to update watchdog configuration
+update_watchdog_config() {
+    # Extract watchdog IP addresses
+    watchdog=$(sudo cat /var/lib/dhcp/* | grep -a "option watchdog" | tail -1 | \
+    awk '{for (i=3; i<=NF; i++) printf "%s ", $i}' | tr -d '";')
+    
+    IFS=', ' read -r -a ip_array <<< "$watchdog"  # Split IPs by comma or space
+
+    # Backup current configuration
+    sudo cp "$config_file" "$config_file.bak"
+    log "Backup of $config_file created successfully."
+
+    # Write static configuration to file
+    {
+        echo "realtime = yes"
+        echo "priority = 1"
+        echo "interface = eth0"
+        echo "interval = 58"
+        echo "ping-count = 1"
+    } | sudo tee "$config_file" > /dev/null
+    log "Static configuration written to $config_file."
+
+    if [ ${#ip_array[@]} -eq 0 ]; then
+        log "No IP addresses found. Watchdog configuration cleared."
+        return 1  # No IP addresses to configure
+    else
+        # Append IPs to config
+        for ip in "${ip_array[@]}"; do
+            echo "ping = $ip" | sudo tee -a "$config_file" > /dev/null
+        done
+        log "Configured watchdog to ping: ${ip_array[*]}"
+
+        # Attempt to restart watchdog service
+        if ! sudo systemctl restart watchdog; then
+            log "Failed to restart watchdog service. Attempting to stop and start."
+
+            # Fallback: stop then start the service
+            sudo systemctl stop watchdog
+            if sudo systemctl start watchdog; then
+                log "Watchdog service started successfully after stop."
+            else
+                log "Failed to start watchdog service after stop."
+                return 1
+            fi
+        else
+            log "Watchdog service restarted successfully."
+        fi
+
+        # Stop watchdog-monitor service if restart/start was successful
+        if sudo systemctl stop watchdog-monitor; then
+            log "watchdog-monitor service stopped successfully."
+        else
+            log "Failed to stop watchdog-monitor service."
+        fi
+
+        return 0  # Successful restart/start
+    fi
+}
+
+# Loop parameters
+interval=30  # Interval to wait between checks
+start_time=$(date +%s)
+end_time=$((start_time + 300))  # 5 minutes in seconds
+
+# Main loop
+while true; do
+    if ! update_watchdog_config; then
+        log "IP addresses found and watchdog restarted. Exiting loop."
+        break
+    else
+        log "No IP addresses found or restart failed. Waiting for $interval seconds before checking again..."
+    fi
+
+    # Check if 5 minutes have passed
+    if [ "$(date +%s)" -ge "$end_time" ]; then
+        log "5 minutes have passed. Stopping the watchdog service."
+        sudo systemctl stop watchdog
+        break
+    fi
+
+    log "Waiting for $interval seconds before checking for IP addresses again..."
+    sleep $interval
+done
+
+# Version 1.5:
+# Created 2024 by Tim Eertmoed @ WiS IT-Solutions GmbH, Germany to work on Raspian as custom PXE init script.

data/service/chromium-monitor.service

@@ -1,16 +1,12 @@
 [Unit]
 Description=A Service to monitor the Kiosk's current site
-After=network.target getty@tty1.service
+After=network.target
 
 [Service]
-ExecStartPre=-/bin/sleep 10
 Type=simple
 User=loginuser
+ExecStartPre=/bin/bash -c 'pgrep -f chromium-browser > /dev/null || exit 1'
 ExecStart=/usr/bin/custom/chromium-monitor
-Restart=on-failure
-RestartSec=5s
-StandardOutput=append:/var/log/chromium-monitor.log
-StandardError=append:/var/log/chromium-monitor.log
 
 [Install]
 WantedBy=multi-user.target

data/service/watchdog-monitor.service

@@ -1,16 +1,10 @@
 [Unit]
 Description=Watchdog Monitor Service
-After=network.target getty@tty1.service
+After=network.target
 
 [Service]
-ExecStartPre=-/bin/sleep 10
 Type=simple
-User=loginuser
+ExecStart=/usr/bin/custom/watchdog-monitor
-ExecStart=/usr/bin/watchdog/watchdog
-Restart=on-failure
-RestartSec=5s
-StandardOutput=append:/var/log/watchdog
-StandardError=append:/var/log/watchdog
 
 [Install]
 WantedBy=multi-user.target

home/wis/.ssh/id_rsa.pub

@@ -1 +0,0 @@
-ssh-rsa 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

install.sh

@@ -11,86 +11,176 @@ print_status() {
     echo -e "${GREEN}✔${NC} ${1} completed."
 }
 
-echo -e "${RED}→${NC} Starting System Update..."
+# Update and setup system and packages
+echo -e "${RED}→${NC} Starting System Update..." | tee -a /var/log/install
 sudo apt update >>/var/log/install 2>&1 && print_status "System Update"
-sudo apt upgrade -y >>/var/log/install 2>&1 && print_status "System Upgrade"
+sudo apt full-upgrade -y >>/var/log/install 2>&1 && print_status "System Upgrade"
-sudo apt dist-upgrade -y >>/var/log/install 2>&1 && print_status "System Dist-Upgrade"
+
+echo -e "${RED}→${NC} Installing required packages..." | tee -a /var/log/install
+sudo apt install --no-install-recommends realvnc-vnc-server xserver-xorg x11-xserver-utils xinit chromium-browser fonts-noto-color-emoji nfs-common watchdog xdotool rsync -y >>/var/log/install 2>&1 && print_status "Required packages installed"
 sudo apt autoremove -y >>/var/log/install 2>&1 && print_status "Autoremove"
 sudo apt clean >>/var/log/install 2>&1 && print_status "Clean"
+sudo rm -rf /var/lib/apt/lists/* >>/var/log/install 2>&1 && print_status "Clear cache"
 
-echo -e "${RED}→${NC} Installing required packages..."
+echo -e "${RED}→${NC} Configuring Raspberry Pi settings..." | tee -a /var/log/install
-sudo apt install --no-install-recommends xserver-xorg x11-xserver-utils xinit chromium-browser fonts-noto-color-emoji nfs-common watchdog xdotool rsync -y >>/var/log/install 2>&1 && print_status "Required packages installed"
+print_status ""
-sudo apt install realvnc-vnc-server overlayroot -y >>/var/log/install 2>&1 && print_status "VNC and Overlayroot installed"
 
-echo -e "${RED}→${NC} Creating user 'loginuser'..."
+# Set needed users
+echo -e "${RED}→${NC} Creating nescessary directorys..." | tee -a /var/log/install
+sudo mkdir -p /overlay >>/var/log/install 2>&1 && print_status "/overlay created"
+
+# Set needed users
+echo -e "${RED}→${NC} Creating user 'loginuser'..." | tee -a /var/log/install
 sudo adduser --disabled-password --gecos "" loginuser >>/var/log/install 2>&1 && print_status "User 'loginuser' created"
 
-echo -e "${RED}→${NC} Setting permissions for 'loginuser'..."
+# Copy required files
-sudo tee /etc/sudoers.d/loginuser >/dev/null << 'EOF'
+echo -e "${RED}→${NC} Copy requiered files..." | tee -a /var/log/install
-loginuser ALL=(ALL) NOPASSWD: /usr/bin/systemctl restart watchdog, /usr/bin/systemctl restart chromium-monitor
+sudo mkdir -p /etc/chromium/policies/managed /etc/systemd/system/getty@tty1.service.d /usr/bin/custom
-loginuser ALL=(ALL) NOPASSWD: /usr/bin/echo, /usr/bin/cp, /usr/bin/sed
+declare -A files=(
-loginuser ALL=(ALL) NOPASSWD: /usr/sbin/reboot, /usr/sbin/dhclient eth0, /usr/bin/fbset
+    ["/root/rps-client/data/config/config.txt"]="/boot/firmware/config.txt"
-loginuser ALL=(ALL) NOPASSWD: /usr/bin/cat /var/lib/dhcp/*
+    ["/root/rps-client/data/config/dhclient.conf"]="/etc/dhcp/dhclient.conf"
-EOF
+    ["/root/rps-client/data/config/override.conf"]="/etc/systemd/system/getty@tty1.service.d/override.conf"
-sudo usermod -aG video loginuser >>/var/log/install 2>&1 && print_status "Permissions for 'loginuser' set"
+    ["/root/rps-client/data/config/disable_password_saving.json"]="/etc/chromium/policies/managed/disable_password_saving.json"
+    ["/root/rps-client/data/config/.bash_profile"]="/home/loginuser/.bash_profile"
+    ["/root/rps-client/data/config/.xinitrc"]="/home/loginuser/.xinitrc"
+    ["/root/rps-client/data/scripts/overlayRoot.sh"]="/sbin/overlayRoot.sh"
+    ["/root/rps-client/data/scripts/ramfsRoot.sh"]="/sbin/ramfsRoot.sh"
+    ["/root/rps-client/data/scripts/squashfsRoot.sh"]="/sbin/squashfsRoot.sh"
+    ["/root/rps-client/data/scripts/remove_unused_kernel.sh"]="/root/remove_unused_kernel.sh"
+    ["/root/rps-client/data/scripts/hostname"]="/usr/bin/custom/hostname"
+    ["/root/rps-client/data/scripts/chromium-monitor"]="/usr/bin/custom/chromium-monitor"
+    ["/root/rps-client/data/scripts/watchdog-monitor"]="/usr/bin/custom/watchdog-monitor"
+    ["/root/rps-client/data/service/hostname.service"]="/etc/systemd/system/hostname.service"
+    ["/root/rps-client/data/service/watchdog-monitor.service"]="/etc/systemd/system/watchdog-monitor.service"
+    ["/root/rps-client/data/service/chromium-monitor.service"]="/etc/systemd/system/chromium-monitor.service"
+)
+RSYNC_OPTS="-a --numeric-ids --info=progress2 --no-owner --no-group"
+for src in "${!files[@]}"; do
+    dst="${files[$src]}"
+    echo "Copying $src to $dst..."
+    sudo rsync $RSYNC_OPTS "$src" "$dst" >>/var/log/install 2>&1 && print_status "$src copied to $dst"
+done
+print_status "All files have been successfully copied"
 
-echo -e "${RED}→${NC} Disabling root login..."
+# Set permissions
+echo -e "${RED}→${NC} Setting file permissions..." | tee -a /var/log/install
+sudo chown loginuser:loginuser -R /home/loginuser >>/var/log/install 2>&1 && print_status "File permissions for 'loginuser' set"
+sudo chown wis:wis -R /home/wis >>/var/log/install 2>&1 && print_status "File permissions for 'wis' set"
+sudo chmod +x /usr/bin/custom/hostname /usr/bin/custom/chromium-monitor /usr/bin/custom/watchdog-monitor /sbin/overlayRoot.sh /sbin/ramfsRoot.sh >>/var/log/install 2>&1 && print_status "Permissions for script files set"
+sudo usermod -aG video loginuser >>/var/log/install 2>&1 && print_status "Permissions for 'loginuser' set"
+echo -e "${RED}→${NC} Setting permissions for 'loginuser'..." | tee -a /var/log/install
+sudo tee /etc/sudoers.d/loginuser >>/var/log/install 2>&1 <<'EOF' \
+&& print_status "Sudo rights for 'loginuser' set"
+loginuser ALL=(ALL) NOPASSWD: /usr/bin/systemctl stop chromium-monitor, /usr/bin/systemctl start chromium-monitor
+loginuser ALL=(ALL) NOPASSWD: /usr/bin/systemctl stop watchdog-monitor, /usr/bin/systemctl start watchdog-monitor
+loginuser ALL=(ALL) NOPASSWD: /usr/bin/cat /var/lib/dhcp/*
+loginuser ALL=(ALL) NOPASSWD: /usr/bin/cp /etc/watchdog.conf /etc/watchdog.conf.bak
+loginuser ALL=(ALL) NOPASSWD: /usr/bin/tee /etc/watchdog.conf, /usr/bin/tee -a /etc/watchdog.conf
+loginuser ALL=(ALL) NOPASSWD: /usr/bin/sed -i
+loginuser ALL=(ALL) NOPASSWD: /usr/bin/sed -r 's/[x]+/,/g'
+loginuser ALL=(ALL) NOPASSWD: /usr/bin/fbset -s
+loginuser ALL=(ALL) NOPASSWD: /usr/bin/hostnamectl set-hostname
+loginuser ALL=(ALL) NOPASSWD: /usr/sbin/dhclient eth0
+loginuser ALL=(ALL) NOPASSWD: /usr/sbin/reboot
+EOF
+
+# Setze TCP-Keepalive
+echo "net.ipv4.tcp_keepalive_time = 60" >> /etc/sysctl.conf
+echo "net.ipv4.tcp_keepalive_intvl = 10"  >> /etc/sysctl.conf
+echo "net.ipv4.tcp_keepalive_probes = 6"  >> /etc/sysctl.conf
+
+# Disable root
+echo -e "${RED}→${NC} Disabling root login..." | tee -a /var/log/install
 sudo tee /etc/ssh/sshd_config >/dev/null << 'EOF'
 PermitRootLogin no
 EOF
 sudo passwd -l root >>/var/log/install 2>&1 && print_status "Root login disabled"
 
-echo -e "${RED}→${NC} Copying required files..."
+# Setup logs
-sudo rsync -a --numeric-ids --info=progress2 --no-owner --no-group \
+echo -e "${RED}→${NC} Creating log files..." | tee -a /var/log/install
-    ./rps-client/boot/ro-root.sh /boot/ro-root.sh \
+sudo touch /var/log/watchdog.log /var/log/chromium-monitor.log /var/log/hostname.log >>/var/log/install 2>&1 && print_status "Log files created"
-    ./rps-client/boot/firmware/ro-root.sh /boot/firmware/ro-root.sh \
+sudo chown loginuser:loginuser /var/log/watchdog.log /var/log/chromium-monitor.log /var/log/hostname.log >>/var/log/install 2>&1 && print_status "Ownership set for log files"
-    ./rps-client/etc/dhcp/dhclient.conf /etc/dhcp/dhclient.conf \
+sudo chmod 777 /var/log/watchdog.log /var/log/chromium-monitor.log /var/log/hostname.log >>/var/log/install 2>&1 && print_status "Permissions set for log files"
-    ./rps-client/etc/systemd/system/hostname.service /etc/systemd/system/hostname.service \
-    ./rps-client/etc/systemd/system/watchdog.service /etc/systemd/system/watchdog.service \
-    ./rps-client/etc/systemd/system/chromium-monitor.service /etc/systemd/system/chromium-monitor.service \
-    ./rps-client/etc/systemd/system/getty@tty1.service.d/override.conf /etc/systemd/system/getty@tty1.service.d/override.conf \
-    ./rps-client/etc/chromium/policies/managed/disable_password_saving.json /etc/chromium/policies/managed/disable_password_saving.json \
-    ./rps-client/home/loginuser/.bash_profile /home/loginuser/.bash_profile \
-    ./rps-client/home/loginuser/.xinitrc /home/loginuser/.xinitrc \
-    ./rps-client/home/wis/.ssh/id_rsa.pub /home/wis/.ssh/id_rsa.pub \
-    ./rps-client/root/remove_unused_kernel.sh /root/remove_unused_kernel.sh \
-    ./rps-client/root/.vnc/config.d/vncserver-x11 /root/.vnc/config.d/vncserver-x11 \
-    ./rps-client/usr/bin/custom/hostname /usr/bin/custom/hostname \
-    ./rps-client/usr/bin/custom/chromium-monitor /usr/bin/custom/chromium-monitor \
-    ./rps-client/usr/bin/custom/watchdog /usr/bin/custom/watchdog >>/var/log/install 2>&1 && print_status "Required files copied"
 
-echo -e "${RED}→${NC} Setting file permissions..."
+# Configure services
-sudo chown loginuser:loginuser -R /home/loginuser >>/var/log/install 2>&1 && print_status "File permissions set"
+echo -e "${RED}→${NC} Configure services..." | tee -a /var/log/install
-
-echo -e "${RED}→${NC} Creating log files..."
-sudo touch /var/log/watchdog.log /var/log/chromium-monitor.log >>/var/log/install 2>&1 && print_status "Log files created"
-
-echo -e "${RED}→${NC} Setting ownership for log files..."
-sudo chown loginuser:loginuser /var/log/watchdog.log /var/log/chromium-monitor.log >>/var/log/install 2>&1 && print_status "Ownership set for log files"
-
-echo -e "${RED}→${NC} Setting permissions for log files..."
-sudo chmod 664 /var/log/watchdog.log /var/log/chromium-monitor.log >>/var/log/install 2>&1 && print_status "Permissions set for log files"
-
-echo -e "${RED}→${NC} Enabling services..."
 sudo systemctl daemon-reload >>/var/log/install 2>&1 && print_status "Daemon reloaded"
-sudo systemctl enable hostname watchdog chromium-monitor vncserver-x11-serviced.service >>/var/log/install 2>&1 && print_status "Services enabled"
+sudo systemctl enable hostname chromium-monitor getty@tty1 >>/var/log/install 2>&1 && print_status "Services enabled"
+sudo systemctl disable watchdog >>/var/log/install 2>&1 && print_status "Watchdog disabled"
 sudo systemctl restart getty@tty1 >>/var/log/install 2>&1 && print_status "getty service restarted"
 
-echo -e "${RED}→${NC} Do you want to clean up unused kernels? (yes/y/ye to proceed):"
+# Set performance
-read -r clean_kernels
+echo -e "${RED}→${NC} Configure performance teaks..." | tee -a /var/log/install
-if [[ "$clean_kernels" =~ ^[Yy](e[Ss]?)?$ ]]; then
+echo "performance" | sudo tee /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor >>/var/log/install 2>&1 && print_status "CPU set to high"
-    echo -e "${RED}→${NC} Cleaning up unused kernels..."
+sudo systemctl mask sleep.target suspend.target hibernate.target hybrid-sleep.target >>/var/log/install 2>&1 && print_status "Powercfg off"
-    sudo bash /root/remove_unused_kernel.sh -u -e >>/var/log/install 2>&1 && print_status "Unused kernels cleaned up"
-else
-    echo -e "${RED}→${NC} Skipping unused kernel cleanup."
-fi
 
-echo -e "${RED}→${NC} Cleaning up installer..."
+# Clean
+echo -e "${RED}→${NC} Cleaning up installer..." | tee -a /var/log/install
 sudo rm -rf ./rps-client >>/var/log/install 2>&1 && print_status "Installer cleaned up"
 
-echo -e "${GREEN}✔${NC} Installation complete. Press any key to reboot..."
+# Configure VNC-Client
+echo -e "${RED}→${NC} Configuring VNC..." | tee -a /var/log/install
+sudo systemctl enable vncserver-x11-serviced.service >>/var/log/install 2>&1 && print_status "VNC service enabled"
+sudo systemctl start vncserver-x11-serviced.service >>/var/log/install 2>&1 && print_status "VNC service started"
+CONFIG_FILE="/root/.vnc/config.d/vncserver-x11"
+if [ ! -d "$(dirname "$CONFIG_FILE")" ]; then
+    sudo mkdir -p "$(dirname "$CONFIG_FILE")"
+    echo -e "${GREEN}✔${NC} Created directory for VNC config." | tee -a /var/log/install
+fi
+echo -e "${RED}→${NC} Do you want to set a VNC password? (y/n):" | tee -a /var/log/install
+read -r config_vnc
+if [[ "$config_vnc" =~ ^[Yy](e[Ss]?)?$ ]]; then
+    sudo vncpasswd
+    echo -e "${GREEN}✔${NC} VNC password has been set." | tee -a /var/log/install
+else
+    echo -e "${GREEN}✔${NC} No VNC password will be set." | tee -a /var/log/install
+fi
+if [ "$(vncpasswd -o)" = 'none' ]; then
+    echo "Authentication=none" >> "$CONFIG_FILE"
+    echo "Geometry=1920x1080" >> "$CONFIG_FILE"
+    echo "#  Version 1.0:" >> "$CONFIG_FILE"
+    echo "#  Created 2024 by Tim Eertmoed, Christian Hampp @ WiS IT-Solutions GmbH, Germany to work on Raspbian as custom PXE init script." >> "$CONFIG_FILE"
+    print_status "VNC config set to no authentication with geometry 1920x1080." >> /var/log/install 2>&1
+else
+    echo "Authentication=none" >> "$CONFIG_FILE"
+    echo "Geometry=1920x1080" >> "$CONFIG_FILE"
+    echo "#  Version 1.0:" >> "$CONFIG_FILE"
+    echo "#  Created 2024 by Tim Eertmoed, Christian Hampp @ WiS IT-Solutions GmbH, Germany to work on Raspbian as custom PXE init script." >> "$CONFIG_FILE"
+    print_status "VNC password is set. Authentication will be required." >> /var/log/install 2>&1
+fi
+
+# Remove old kernels
+echo -e "${RED}→${NC} Do you want to clean up unused kernels? (y/n):" | tee -a /var/log/install
+read -r clean_kernels
+if [[ "$clean_kernels" =~ ^[Yy](e[Ss]?)?$ ]]; then
+    echo -e "${RED}→${NC} Cleaning up unused kernels..." | tee -a /var/log/install
+    echo -e "y\ny" | sudo bash ./root/remove_unused_kernel.sh -u -e >>/var/log/install 2>&1 && print_status "Unused kernels cleaned up"
+else
+    echo -e "${RED}→${NC} Skipping unused kernel cleanup..." | tee -a /var/log/install
+    echo -e "${GREEN}✔${NC} Cleanup has been skipped" | tee -a /var/log/install
+fi
+
+
+# Create squashfs
+#echo -e "${RED}→${NC} Do you want to create a squashfs image of the system and copy it to the server? (y/n):" | tee -a /var/log/install
+#read -r create_squash
+#if [[ "$create_squash" =~ ^[Yy](e[Ss]?)?$ ]]; then
+#    echo -e "${RED}→${NC} Creating squashfs image..." | tee -a /var/log/install
+#    SQUASH_IMAGE="/tmp/rootfs.squashfs"
+#    SERVER_IP="192.168.120.239"
+#    SERVER_DIR="/nfs/live/rootfs"
+#    sudo mksquashfs / "$SQUASH_IMAGE" -e boot dev proc sys tmp run media mnt lost+found var/log >>/var/log/install 2>&1 && print_status "SquashFS created"
+#    echo -e "${RED}→${NC} Copying squashfs image to NFS server..." | tee -a /var/log/install
+#    sudo rsync -avh "$SQUASH_IMAGE" "$SERVER_IP:$SERVER_DIR" >>/var/log/install 2>&1 && print_status "SquashFS copied to server"
+#    sudo rm "$SQUASH_IMAGE" >>/var/log/install 2>&1 && print_status "Temporary squashfs file removed"
+#else
+#    echo -e "${GREEN}✔${NC} SquashFS creation skipped." | tee -a /var/log/install
+#fi
+
+
+# Finish
+echo -e "${GREEN}✔${NC} Installation complete. Press any key to exit..." | tee -a /var/log/install 2>&1
 read -n 1 -s
-sudo reboot
 
 # Version 1.2:
 # Created 2024 by Tim Eertmoed, Christian Hampp @ WiS IT-Solutions GmbH, Germany to work on Raspian as custom pxe init script.

root/.ssh/id_rsa.pub

@@ -1 +0,0 @@
-ssh-rsa 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

root/.vnc/config.d/vncserver-x11

@@ -1,4 +0,0 @@
-Authentication=None
-
-#  Version 1.0:
-#  Created 2024 by Tim Eertmoed, Christian Hampp @ WiS IT-Solutions GmbH, Germany to work on Raspian as custom pxe init script.

usr/bin/custom/chromium-monitor

@@ -1,58 +0,0 @@
-#!/bin/bash 
-
-LOGFILE="/var/log/chromium-monitor.log"
-
-get_monitor() {
-    sudo cat /var/lib/dhcp/* | grep -a "option monitor" | tail -1 | \
-    awk '{ s = ""; for (i = 3; i <= NF; i++) s = s $i " "; print s}' | \
-    awk -F '"' '{print $2}'
-}
-
-get_current_window() {
-    DISPLAY=:0 xdotool getwindowfocus getwindowname | awk -F '- Chromium' '{print $1}'
-}
-
-monitor=""
-while [ -z "$monitor" ]; do
-    monitor=$(get_monitor)
-    echo "Current monitor: $monitor" >> $LOGFILE  # Debug output
-    if [ -z "$monitor" ]; then
-        sleep 5
-    fi
-done
-
-monitor_md5=$(echo -n ${monitor^^} | sed -e 's/^[[:space:]]*//' | md5sum | awk '{print $1}')
-echo "Monitor MD5: $monitor_md5" >> $LOGFILE  # Debug output
-
-while true; do
-    new_monitor=$(get_monitor)
-    new_current=$(get_current_window)
-
-    # Log the current state
-    echo "New monitor: $new_monitor" >> $LOGFILE  # Debug output
-    echo "New current window: $new_current" >> $LOGFILE  # Debug output
-
-    if [ -n "$new_monitor" ] && [ -n "$new_current" ]; then
-        new_monitor_md5=$(echo -n ${new_monitor^^} | sed -e 's/^[[:space:]]*//' | md5sum | awk '{print $1}')
-        current_md5=$(echo -n ${new_current^^} | sed -e 's/^[[:space:]]*//' | md5sum | awk '{print $1}')
-
-        # Log the computed MD5 hashes
-        echo "New monitor MD5: $new_monitor_md5" >> $LOGFILE  # Debug output
-        echo "Current window MD5: $current_md5" >> $LOGFILE  # Debug output
-
-        if [ "$new_monitor_md5" != "$monitor_md5" ] && [ "$current_md5" != "$monitor_md5" ]; then
-            echo "Mismatch detected. Rebooting now." >> $LOGFILE
-            sudo reboot
-            exit 1
-        fi
-    else
-        echo "Either monitor or current is not available, skipping check." >> $LOGFILE
-    fi
-
-    # Log the status before sleeping
-    echo "Sleeping for 5 seconds before the next check..." >> $LOGFILE
-    sleep 5s
-done
-
-#  Version 1.0:
-#  Created 2024 by Tim Eertmoed, Christian Hampp @ WiS IT-Solutions GmbH, Germany to work on Raspian as custom pxe init script.

usr/bin/custom/watchdog

@@ -1,46 +0,0 @@
-#!/bin/bash
-
-# Log file
-log_file="/var/log/watchdog.log"
-
-# Extract watchdog IP addresses
-watchdog=$(sudo cat /var/lib/dhcp/* | grep -a "option watchdog" | tail -1 | \
-awk '{for (i=3; i<=NF; i++) printf "%s ", $i}' | tr -d '";')
-IFS=' ' read -r -a ip_array <<< "$watchdog"
-
-# Configuration file
-config_file="/etc/watchdog.conf"
-
-# Backup current configuration
-if sudo cp "$config_file" "$config_file.bak"; then
-    echo "Backup of $config_file created successfully." >> "$log_file"
-else
-    echo "Failed to create backup of $config_file." >> "$log_file"
-fi
-
-# Clean existing configurations
-sudo sed -i '/ping/d' "$config_file"
-sudo sed -i '/^interval/d' "$config_file"
-
-# Set interval
-echo "interval = 60" | sudo tee -a "$config_file" > /dev/null
-
-if [ ${#ip_array[@]} -eq 0 ]; then
-    echo "No IP addresses found. Watchdog configuration cleared." >> "$log_file"
-    sudo systemctl stop watchdog
-else
-    for ip in "${ip_array[@]}"; do
-        echo "ping = $ip" | sudo tee -a "$config_file" > /dev/null
-    done
-    echo "Configured watchdog to ping: ${ip_array[*]}" >> "$log_file"
-fi
-
-# Restart watchdog service
-if sudo systemctl restart watchdog; then
-    echo "Watchdog service restarted successfully." >> "$log_file"
-else
-    echo "Failed to restart watchdog service." >> "$log_file"
-fi
-
-#  Version 1.1:
-#  Created 2024 by Tim Eertmoed @ WiS IT-Solutions GmbH, Germany to work on Raspian as custom pxe init script.